Just How to Replace a Tub
Just How to Replace a Tub
Blog Article
How do you feel about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a bathtub isn't specifically rocket science, but it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably tough project. If the old bathtub is easily accessible, the task can move speedily; if you need to open a wall surface to eliminate the old bathtub and place the new bath tub, the task is much harder. In either situation, the project is within a residence handyman's skills, although you will certainly need an assistant to move out the old bathtub and also set in the brand-new one. Make sure you have certified yourself for the job and also are comfortable attempting it. Instead of employing a contractor to take over a halfway-completed task, it is better to take into consideration employing one before you start. Possibilities are you might need an expert plumber to make tube connections.
This short article will certainly aid you install a new tub in your washroom if you have already gotten a brand-new tub as well as do not require to transform the arrangement of your previous supply of water pipelines.
Your devices and material checklist must consist of the following:
Getting ready for the Setup
To start with, the sustaining structure provided with the bathroom should be fitted (if required) according to the supplier's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to make certain that if the tap features a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid stress on the bathtub.
Fit the flexible faucet ports to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you use all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now prepare to be fitted in its last position.
Removing Old Touches
If you need to change old taps with new ones as a part of your installation, after that the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be fairly bothersome because of the limited gain access to that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will originate from the pipes. When the supply pipes have been gotten rid of, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing substance.
Prior to carrying on to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Setting up the Bath tub
Utilizing both wood boards under its feet, position the bath tub in the required position. The wooden boards are valuable in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four little factors.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by examining the level as well as changing the feet on the bath tub till the spirit level reads level.
To set up faucets, fit all-time low of the outermost flexible tap port to the proper supply pipeline by making a compression sign up with; after that do the same for the other tap.
Turn on the water system as well as examine all joints and also new pipework for leaks as well as tighten them if needed. Load the bathtub and likewise examine the overflow electrical outlet and the normal outlet for leakages.
Ultimately, fix the bath paneling as described in the producer's user's manual. Tiling and also securing around the bathtub should wait up until the tub has actually been made use of a minimum of once as this will settle it into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the tap as well as the other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin guaranteeing that the washers are in place between the tap and also the sink. Safeguard the faucet in position with the supplier given backnut. When the tap is securely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with typical tap connectors. The previous kind ought to be connected to the faucet finishes initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a rigid seal, creating the water to pass through the wall between the bathroom as well as the tiling, resulting in difficulties with moisture and feasible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components as well as installations. They are offered in tubes and cartridges, as well as are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water before sealing, to permit the motion experienced when the bathtub is in use. The sealer can crack relatively very early if you do not consider this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I stumbled upon that review about A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the web. Remember to set aside a second to share this blog entry if you enjoyed it. Thanks a lot for your time. Come back soon.
Book An Appointment Report this page